QJB Submersible Mixer

Du'an Environmental Protection QJB10/12-620/3-480S Submersible Mixer 

Installation Diagram of Stainless Steel Sewage Mixer

Motor Power 10KW

Impeller Diameter 620mm

Impeller Speed 480r/min

Full Copper Coil Motor

Du'an Environmental Protection QJB Submersible Mixer, Main Component Materials of Submersible Mixer

Mixing equipment mainly includes submersible mixers and vertical mixers.

The technical standards and quality of submersible mixer equipment should be equivalent to imported brands like KBS, and manufacturer authorization must be provided.

Submersible mixer equipment should use mature products with advanced technology and provide operational performance records of similar equipment in no less than three projects over the past five years.

Submersible Mixer Technical Agreement:

1. Scope of Supply

The sewage mixer produced by Jiangsu Du'an Environmental Protection is a complete unit, equipped with guide rods, lifting devices, underwater cables, fixing bolts, fasteners, and accessories necessary for installation and safe operation.

2. Technical Requirements

The submersible mixer should be capable of continuous and intermittent operation under fully submerged conditions. It must operate smoothly without vibration throughout its service life, with a design lifespan of 15 years and a mean time between failures of 8000 hours.

Each submersible mixer should work in sewage and must promote the flow of sewage.

The submersible mixer should rotate smoothly without jamming, stalling, or vibration.

The submersible mixer should undergo a sealed air pressure test at 3 kg/cm² for 5 minutes without leakage.

Each submersible mixer is equipped with a stainless steel guide rod and stainless steel wire rope for free lifting and steering.

1) Terminal Box

The motor terminal box has a protection rating of IP68 and must be completely sealed from the surrounding liquid.

2) Cooling

Motor cooling is achieved through heat conduction from the stator to the housing.

3) Shaft Seal

An independent high-quality sealing system is used to ensure that even if the lower seal fails and liquid enters the stator chamber, it will not contact the bearings or stator. The mechanical seal is made of corrosion-resistant silicon carbide/silicon carbide, suitable for a pH range of 6-9. The mechanical seal should be maintenance-free, resistant to thermal shock, and capable of emergency operation.

The manufacturer should ensure the mechanical seal has a service life of no less than 25,000 hours.

4) Shaft

The motor shaft is a single shaft, reliably sealed without contact with the liquid.

5) Submersible Mixer Impeller

Designed with a propulsive anti-twist curve, the impeller has a stamped structure, is lightweight, high-strength, and well-balanced. The optimized impeller surface has a self-cleaning function to avoid clogging and scaling.

Equipped with a flow guide cover to rectify flow, increase axial flow and directionality, and enhance circulation flow.

6) Motor

The motor should be a three-phase squirrel cage motor, 3-phase 380V, 50Hz, with protection rating IP68 and insulation class F. The motor should not overload even under heavy mixing loads. It should start no less than 15 times per hour, with the average temperature rise of the stator windings not exceeding 80°C. The stator should be thermally pressed into the stator chamber without the need for drilling holes for bolts, pins, or other connecting devices.

7) Bearings

The impeller shaft is supported by a double-row angular contact ball bearing and a single-row deep groove ball bearing. To ensure long-term and reliable operation, imported NSK bearings are used with a service life of no less than 100,000 hours.

8) Cable and Cable Seal

The motor should be equipped with underwater control and power cables, reliably sealed. If the power cable is multi-core, each cable must be individually sealed. Cables should extend into the terminal box and be sealed with reusable rubber seals; resin or other canned sealing materials are not allowed. Each cable should be equipped with a cable net or cable clamp to suspend the cable from a hook and support its weight.

9) Leakage Sensor

A sensor is provided in the sealing cavity to detect liquid leakage. All signals should be monitored separately, and alarm signals should be issued before serious damage occurs to the impeller or motor.

10) Thermal Protection

Each phase of the motor is protected by a normally closed temperature sensor. The three sensors should be connected in series, activating at 140°C, and connected to the control cabinet.

11) Installation and Lifting System

Du'an Environmental Protection provides a complete set of installation and fastening materials for the submersible mixer. The installation system should include guide rails, wire ropes, an arm-type lifting frame, and a hand-operated hoisting device.

Main Components of Jiangsu Du'an Environmental Protection QJB High-Speed Submersible Mixer

(1) Fully assembled submersible mixer;

(2) Matching submersible motor;

(3) Complete installation system (guide rails, brackets, fasteners, etc.);

(4) A set of shared lifting equipment (movable lifting bracket, lifting hoist, stainless steel lifting chain, etc.);

(5) Submersible cable for each mixer;

(6) Submersible mixer protection components, including leakage protection, temperature protection, and protection controllers;

(7) Local control cabinet and junction box;

(8) All connecting accessories and fasteners for installation (including stainless steel chemical anchor bolts, nuts, washers, etc.);

(9) Two-year supply of spare parts and matching tools within the warranty period.

WQ Submersible Sewage Pump | AS Cutter Pump | AV Scraper Suction Pump | QJB Submersible Mixer | WL Vertical Sewage Pump | WQB Explosion-proof Sewage Pump | LS Vertical Pipeline Pump | Coupling Device | LB-05 Leakage Protector | NS-4 Comprehensive Protector | INT Thermal Protector | FK2 Float Switch | ZQB Submersible Axial Flow Pump | SQB Hyperboloid Mixer | QJB-W Sludge Return Pump | QJB Submersible Flow Maker | QXB Submersible Aerator | QSB Submersible Jet Aerator | Bar Screen | Scraper Suction Machine | Prefabricated Pump Station | Frame Mixer | Paddle Mixer | Shaftless Screw Conveyor | Grit Separator | Belt Conveyor |